Laying instructions

Leginstructies_GOED

 

General

  • The processing guidelines must always be observed for an optimum result.
  • Only use adhesive from one product line of one and the same supplier.
  • Check the entrance mat before laying to ensure that the material matches with regard to the sample and for any errors.
  • Check before laying whether the specifications of the entrance mat match the intended user objectives.

Preparation

  • The base must be clean, have tensile strength and be compression resistant, dirt free, grease free and dry permanently.
  • Irregular floors must be levelled to cover old adhesive layer and/or bitumen product residue.

General laying instructions

  • The minimum temperature of the subfloor must at least be 15 °C.
  • The minimum ambient temperature must be +/- 18 °C.
  • The relative humidity may not be higher than 70%.
  • The entrance mat and required tools must at least acclimatise for 24 hours under the aforementioned conditions before installation.
  • Direct sunlight and radiation from heat sources must be prevented during installation.
  • Install the entrance material in the length and/or walking direction as much as possible for a beautiful and stronger result.

Installation method per situation

SMALL SURFACE AREAS UP TO 5 M² (SUCH AS MATS for small fits)
  • You can lay the entrance mat loose on level, soft or dry bases.
  • We recommend gluing the entrance mat on to the base or to fit it in place using double-sided tape if possible.
  • We recommend using underlay that is suitable for both the entrance mat and the relevant floor when laying loose on carpet and/or harder floors.
  • Take into account a possible stretch or shrinkage of at most 0.5%.
LARGE SURFACE AREAS OVER 5 M² (ENTRANCE AREAS IN LARGE ROOMS)
  • Areas larger than 5 m² must be fully glued.
  • The entrance mat must be laid tension free and level after which it must be rubbed and rolled so that it sticks properly.
  • Always strictly follow the adhesive instructions of your adhesive producer.

General adhesive instructions

  • We recommend using a suitable dispersion adhesive (maximum humidity of the floor < 2.5%) for gluing on to absorbing (porous) bases and levelled areas.
  • We recommend using a suitable 2-component PU adhesive for gluing on sealed (non-porous) bases.
  • Contact adhesive must be used for laying on stairs.
SUITABLE ADHESIVE types FOR PVC PRODUCTS

We recommend the following for gluing on to absorbing (porous) bases and levelled areas:

  1. Wet gluing:
  • Eurocol: 646 Eurostar Premium
  • UZIN: UZIN KE 66

All to be applied using a TKB A2 adhesive spreader.

  1. Dry gluing:
  • Sigan 1 (in combination with Planus)

We recommend the following for gluing on to elastic (non-porous) bases and levelled areas:

  1. Wet gluing:
  • Eurocol: 646 Eurostar Premium
  • UZIN: UZIN KR 430

All to be applied using a TKB A2 adhesive spreader.

  1. Dry gluing:
  • Sigan 2
SUITABLE ADHESIVE types FOR S-FLX PRODUCTS

We recommend the following for gluing on to absorbing (porous) bases and levelled areas:

  1. Wet gluing:
  • Eurocol: 140 Euromix PU
  • UZIN: UZIN KE 66

All to be applied using a TKB A2 adhesive spreader.

  1. Dry gluing:
  • Sigan 1 (in combination with Planus)

We recommend the following for gluing on to elastic (non-porous) bases and levelled areas:

  1. Wet gluing:
  • Eurocol: 140 Euromix PU
  • UZIN: UZIN KR 430

All to be applied using a TKB A2 adhesive spreader.

  1. Dry gluing:
  • Sigan 2